SKU:

EL-50448 Tire Pressure Monitor Sensor TPMS Activation Tool OEC-T5
EL-50448胎压监测传感器TPMS激活工具OEC-T5
条码:6922887112741
HSCode:90308200
批量修改原始型号
采购:Felix  编辑:Shadow  产品经理:caifeng

Features
1. For GM vehicles equipped with a 315 or 433 MHz Tire Pressure Monitoring (TPM) system, a "Sensor Re-Learn Procedure" must be performed after tire rotations, Remote Control Door Lock Receiver Module replacement or Tire Pressure Sensor replacement. This re-learn procedure can be performed by using special tool EL-50448.
2. Also works on 2014 GM models
3. The tire pressure sensor on models in & after 2012 can be read, only with some specified diagnostic tools.

Note
Before tire pressure monitoring system works normally properly, the body control module will record ID information of each position in the tire pressure sensor; and use the following methods to read the tire pressure sensor after replacing a tire or wheel speed sensor. Please refer to the specific methods as follows:
Step 1: Enter leaning mode
- Set the gearshift lever to "P"
- Put the ignition switch to "ON"
- Enter the interface of tire pressure display by DIC
- DIC shows "Press Set / Ctrl to re-learn"
- Press "Set / Ctrl"
- The turn signal is lighted for 3 seconds and the horn beep sound twice to enter the learning mode
Step 2: Read tire pressure sensor information
- Start from the front-left wheel, make the J-46079 or diagnostic Tool EL-50448 antenna up against the valve core position & close to the rim of the tire sidewall
- El-50448 tire pressure tool starts by the start switch
- Successful to read the tire pressure sensor information when the horn bleeps once
Step 3: Same method to read other tire pressure information
- Follow the instruction above to read tire pressure of the front-right, rear-right, rear-left wheels.
- Turn signals is lighted for 3 seconds and the horn bleeps twice when the learning is complete.


1. 对于配备315或433 MHz轮胎压力监测(TPM)系统的GM车辆,必须在轮胎旋转,更换遥控门锁接收器模块或更换轮胎压力传感器后执行“传感器重新学习程序”。 可以使用专用工具EL-50448执行该重新学习过程。
2. 也适用于2014款GM车型。
3. 只能使用某些指定的诊断工具读取2012年及之后型号的轮胎压力传感器。

注意
在胎压监测系统正常工作之前,车身控制模块将记录轮胎压力传感器中每个位置的ID信息;更换轮胎或车轮速度传感器后,请使用以下方法读取轮胎压力传感器。请参考具体方法如下:
第1步:进入学习模式
- 将换档杆设置为“P”
- 将点火开关置于“ON”位置
- 通过DIC输入轮胎压力显示界面
- DIC显示“按Set / Ctrl重新学习”
- 按“设置/ Ctrl”
- 转动信号点亮3秒钟,并发出哔哔声两次进入学习模式
第2步:阅读轮胎压力传感器信息
- 从左前轮开始,使J-46079或诊断工具EL-50448的天线靠近阀芯位置并靠近轮胎侧壁边缘
- El-50448轮胎压力工具由启动开关启动
- 当喇叭发出一次哔声时,成功读取轮胎压力传感器信息
步骤3:读取其他轮胎压力信息的方法相同
- 按照上述说明读取右前,右后,左后轮的轮胎压力。
- 转弯信号点亮3秒钟,当学习完成时,喇叭发出两次哔哔声。


代码:

Specification:
General
Material Plastic
Size 15cm*9cm*3cm
Weight 280g
Package weight
One package Weight 0.31kgs / 0.68lb
One Package Size 20.0cm * 13.0cm * 3.5cm / 7.87inch * 5.12inch * 1.38inch
Qty per Carton 10
Carton Weight 3.38kgs / 7.45lb
Carton Size 22cm * 28cm * 26cm / 8.66inch * 11.02inch * 10.24inch

代码: