SKU:

5V/12V WIFI Network Automatic Time Synchronization Digital Electronic Clock Module, Color: Blue
5V/12V WIFI网络自动对时数码电子钟芯模块，颜色：蓝色
条码：6922105240727
HSCode：90308200
批量修改原始型号 		采购：Felix  编辑：Leah  产品经理：caifeng


1. Embedded installation of WiFi timing clock module, DC5-20V power supply
2. It has 8 levels of adjustable brightness and an automatic brightness function (the display automatically changes to level 1 brightness after 19:00 in the evening, and automatically changes to the brightness value in the Ld setting after 7:00 in the morning)
3. Equipped with backup memory battery, the power outage time is stable
4. Support time zone, daylight saving time, 12/24 hour settings, available abroad
5. WiFi configuration information will be memorized. After configuring WiFi, as long as the WiFi signal is valid, it will automatically connect to WiFi to obtain the network time, keeping the time accurate for a long time.
6. Time zone, automatic brightness, brightness and other function settings can be set with buttons, or you can use your mobile phone to connect to the hotspot of the electronic clock and use the mobile phone's browser to access 192.168.4.1 for web configuration
7. The daylight saving time function can be configured through the web page
8. Working voltage: DC5.0~20V
9. Frame size: 22x58mm
10. Installation opening size: 19.5x56mm
11. Temperature display range: -35~105 degrees Celsius

Introduction to distribution network networking: Hotspot links only support the 2.4G frequency band. Basically all routers on the market support it, but some are merged settings. It is recommended that the router settings split the 2.4G and 5.8G frequency bands before distributing the network.
1. Power on the electronic clock. After 10 seconds, open the mobile phone WLAN configuration page, find the WiFi signal starting with Config-, and use the password 33669999 to connect the mobile phone to the WiFi. If it prompts "This WiFi cannot access the Internet", please choose to stay connected. Then open the mobile browser and enter 192.168.4.1 to manually open the configuration page, as shown in Figure 2 (After the mobile phone is connected to Config-xxx, if the 192.168.4.1 address browser cannot be entered, please try to turn off the mobile phone data traffic and try several times, but it will not be accessible. , you can power off the clock and try again)
2. Click the Configure WiFi button to open the interface in Figure 3
3. Enter your home WiFi name and WiFi password, and click Save. If the operation is correct, the electronic clock will automatically connect to WiFi to set the time online. After the electronic clock is connected to WiFi, the blue light will turn solid (tip: electronic clocks can also be used) Connect to your phone’s hotspot to check the time online)

1. 嵌入式安装WiFi对时时钟模块，DC5-20V供电
2. 具备8级亮度可调，有自动亮度功能（晚上19:00后显示自动变成1级亮度，早上7:00后自动变成Ld设置里的亮度值）
3. 带有后备记忆电池，掉电时间不乱
4. 支持时区、夏令时、12/24小时设置，国外可用
5. WiFi配置信息会记忆，配置好WiFi后，只要WiFi信号有效就会自动连接WiFi获取网络时间，保持时间长期精准
6. 时区、自动亮度、亮度等功能设置可以用按键设置，也可以用手机连上电子钟的热点后，用手机的浏览器访问192.168.4.1进行网页配置
7. 夏令时功能可通过网页配置
8. 工作电压： DC5.0~20V
9. 外框尺寸：22x58mm
10. 安装开孔尺寸：19.5x56mm
11. 温度显示量程：-35~105摄氏度

配网联网介绍：热点链接只支持2.4G频段，市面上路由器基本上都支持，但是有些是合并设置，建议路由器设置将2.4G和5.8G频段拆分后在配网
1. 给电子钟上电，10秒后，打开手机WLAN配置页，找到以 Config- 开头的WiFi信号，使用密码33669999让手机连上该WiFi，如果提示"该WiFi不能上网"请选择 保持连接.然后打开手机浏览器输入192.168.4.1手动打开配置页，如图2（手机连上Config-xxx后，如果192.168.4.1地址浏览器无法进入，请尝试关闭手机数据流量多试几次,扔无法访问，可以将时钟断电，重新通电尝试）
2. 点击 Configure WiFi 按钮，打开图三界面
3. 输入您家的WiFi名称,和WiFi密码，点击保存，如果操作无误,电子钟将自动连接WiFi上网对时，电子钟连上WiFi后蓝色灯变成长亮（提示：电子钟也可以连接手机的热点来上网对时哦）
代码：

Specification:
Package weight
One package Weight 0.05kgs / 0.11lb
One Package Size 10.0cm * 6.0cm * 4.0cm / 3.94inch * 2.36inch * 1.57inch
Qty per Carton 200
Carton Weight 9.5kgs / 20.94lb
Carton Size 42cm * 38cm * 32cm / 16.54inch * 14.96inch * 12.6inch

代码：